|
Model No: 8912AZ
Thanks you
for choosing our Rear-view camera and monitor.
Please install and use the product in accordance with our operating
instructions. We will provide quality and reliable service for a variety of
vehicles including cars, trucks, and so on. Our implements rigid quality
control and testing to ensure the best performance of the product as well as
satisfactory service for you.
Packing list:
-
Rearview Camera
-
2.4ghz
Wireless TFT-LCD Monitor
-
Mount
Holder
-
+12/+24
Volt Car Power Adapter
-
Monitor
Wiring Harness
-
Wedge
Gasket
-
8m
Video Cable (optional)
-
1.5m
Connect Cable for Video Cable (optional)
-
License
Plate Screws
-
Sheet
Metal Screw
-
Grommet
-
Cable
Ties
-
License
Plate Screws
-
In-Line
Wire Connectors
-
Installation
Installation of the
camera:
-
Loosen the license plate
bolt or screw, and then remove the license plate on the rear of your
car.
-
Drill one hole for power
cable on the top-middle of the license plate location. If your car have
and existing hole, you can skip the step.
-
Peel the backing paper of
the bracket.
-
Paste the camera and tow
the power wire into the car through the interstices of the car. Note: in
wired mode, user also need put the connect cable through the car body to
the wired monitor.
-
Adjust the camera to a
suitable angle. Then Reinstall the license plate and bolt/screw.
-
A detector to find the
power: how to find the power from the reverse light? Introductions:
black clamp connects to the ground wire. Use the red pen to find the
power from the reverse light until the LED light is on. Then connect our
red power line to the power from the reverse light, and the black to the
ground wire.
Installation of the
monitor:
-
Using the mount holder to
install the monitor. Mount holder is stamped on the front window glass.
-
Connect power of the
monitor, there are two methods as following:
-
according the same
steps, to find the power from the car power circuit in front, and
connect the cables correctly.
-
use the car power
adapter included in the package to get the power.
Note: When your use a wired monitor, please connect the video input
port of monitor to the video output port of camera, the camera will
automatically output signal to the monitor. The camera is compatible
with both wired and wireless.
In-Line Wire Connector
Instructions
The camera
can be wired directly to the reverse light circuit by stripping the reverse
light wires then twisting the camera wires to the exposed reverse light
wires. Once connected, wrap with electrical tape. Do not attempt this if you
are not knowledgeable with electrical installation practices.
Testing the System
-
Re-attack the negative
battery cable of vehicle.
-
Engage the parking brake
and turn the ignition key to the ON position. DO NOT start the vehicle.
Put the gear shift into reverse.
-
The camera will start
broadcasting, and the monitor will detect the signal and turn itself ON.
If the monitor does not come ON press the ON/OFF button.
-
If the image does not
match your rear view mirror, press the top button on the monitor to
change the image until it matches your rear view mirror.
-
When you take the gear
shift out of reverse the camera will turn OFF, and the monitor will turn
black.
There are
four different views for the monitor, each time the Image Orientation button
is pressed the image will change.
There
different views allow you to mount the camera and/or monitor either right
aide up or upside down and still display the image correctly on the monitor.
The image displayed should match your rear view mirror. After testing the
unit, fully tighten the license plate bolts. Route all wire behind interior
panels or under carpeting so they are hidden. Use supplied cable ties to
neatly gather any excess wire. Keep camera lens and monitor clean to ensure
optimum picture quality.
Specifications
|
CAMERA |
Items |
8912AZ |
|
Imaging Sensor |
CMOS |
|
Total Pixels |
720×576(PAL) 720×480(NTSC) |
|
Horizontal View Angle |
80 degree |
|
Transmission Frequency |
2468MHz |
|
Transmission Power |
2mW/FCC, 10mW/CE |
|
Minimum Illumination |
5Lux(IR OFF)/0Lux(IR ON) |
|
IR Night Range |
3m |
|
Modulation Type |
FM |
|
Bandwidth |
18MHz |
|
Power Supply |
+12/+14VDC |
|
Consumption Current (Max.) |
100mA(IR OFF)&130mA(IR ON) |
|
Dimensions (W×D×H) |
370×55×35(mm) |
|
Weight (about) |
240g |
|
Monitor |
LCD Screen Type |
3.6" TFT-LCD |
|
Effective Pixels |
960×240 |
|
Video System |
PAL/NTSC |
|
Transmission Frequency |
ISM 2,400~2,483MHz |
|
Color Configuration |
R.G.B. delta |
|
Received Sensitivity |
≤-85dBm |
|
Consumption Current (Max.) |
250mA |
|
Unobstructed Effective Range |
50m |
|
Dimensions (W×D×H) |
108×37×75(mm) |
|
Weight (About) |
165g |
|
Power Supply Voltage |
+12/+24VDC |
|
|
Operating Temperature |
-10°C~+50°C/+14°C~+122°C |
|
Operating Humidity (Max.) |
85%RH |
-
*
Channel Frequency: CH1=2,414MHz; CH2=2,432 MHz;
CH3=2,450 MHz; CH4=2,468 MHz; only CH4 is
available.
-
*
Actual transmission range may vary according to the weather,
location, interference and building construction.
-
*
All the specifications are subject to minor change without prior
notice.
FCC Information
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
-
This
device may not cause harmful interference
-
This
device must accept any interference received, including interference
that may cause undesired operation.
Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
|
ATSC HDTV Tuners Converter Boxes
Specials ...
Shipping & Returns